KDS RC HeliShop
  Home » Artikelcatalogus » FPV / drone onderdelen » KDS Kylin FPV 210 onderdelen » Wraith 32 25 Mijn account  |  Inhoud winkelwagentje  |  Afrekenen   
CategoriŽen
Helicopters (53)
Helicopter onderdelen (1297)
FPV racing drones / frame's (39)
FPV / drone onderdelen (218)
  KDS Kylin FPV 210 onderdelen (48)
  KDS Kylin FPV 250 onderdelen (86)
  Armattan Jappalura (13)
  Armattan Chameleon (22)
  Gemfan propellors (6)
  Motoren cobra/luminier/kylin (7)
  FPV camera's (13)
  Videotransmitters en antennes (14)
  Flightcontrolers en PDB en ESC (9)
Mini helicopters Quadcopters (4)
Rotorbladen Wieken en Vleugel (46)
Zenders en Ontvangers (15)
Li-po accu's (39)
Upgrades (44)
Laders en voedingen (20)
Stekker kabels en verloopkabels (96)
Elektronica (42)
Voordeelpakketten (3)
FPV air gate en vlaggen (8)
Gereedschappen (25)
Accessoires (24)
Rompen (3)
Verwachte producten
Vliegtuigen (1)
Camera's en FPV bril (7)
Demo helicopters (5)
Demo/gebruikt (1)
Schaalrompen compleet met heli
autos (1)
Aanbiedingen
Nieuw
Ga naar...
Aanbiedingen  meer
KDS K-7X II 2.4Ghz zender met K-8X ontvanger inclusief aluminium
KDS K-7X II 2.4Ghz zender met K-8X ontvanger inclusief aluminium
€100.00
€81.35
Nieuwe artikelen  meer
KF-RUNCAM EAGLE 2 - (16:9) (BLACK) (2.5LENS)
KF-RUNCAM EAGLE 2 - (16:9) (BLACK) (2.5LENS)
€55.00
Informatie
Verzendwijze
Retour & privacy
Voorwaarden
Reparatieservice
Over ons
Neem contact op
KF-68 Wraith32 Mini BLHELI32 ESC, 2-6S, 25A, 10x20mm
[Wraith 32 25]
€15.00
KF-68  Wraith32 Mini BLHELI32 ESC, 2-6S, 25A, 10x20mm
klik om te vergroten

 

Airbot Wraith32 Mini ESC (32bit ESC’s) (2-6S) (Dshot 1200) (25Amp) (BLHeli_32 ESC’s)

 

Airbot Wraith32 Mini ESC (32bit ESC’s) (2-6S) (Dshot 1200) (25Amp) (BLHeli_32 ESC’s)

If you’re hunting for the smallest blheli_32 capable 32bit ESC’s, the Airbot Wraith32 Mini ESC’s will certainly fit the bill providing 25Amps of power. The Airbot Wraith32 Mini ESC runs in conjunction with an ARM 32bit compatible MCU, such as the Omnibus F7 Flight Controller. That being said, the Wraith32 Mini can run input signals with lower latency, at faster rates, smooths out the RPM band, is capable of both voltage and current monitoring and limiting, as well as offering customization of the brake on stop force. Unlike current ESC’s, the Wraith32 Mini ESC has A LOT of room to grow and wide compatibility range with future products. One of the nicest features with the Wraith32 is the auto timing feature, which (essentially) is designed to offer the pilot the smoothest and most efficient flight experience available, which is a freestyle pilot’s dream come true! When compared with an appropriate flight controller the Airbot Wraith32 Mini ESC is capable of Dshot 1200 up to 32kHz. Configuration via transmitter is in development which means you may soon be able to make ESC changes via the Omnibus F7’s built-in OSD!!!

 

Features:

  • 32bit Compatible ESC (blheli_32)
  • 25Amps
  • Dshot 1200 up to 32kHz
  • Incredibly small size
  • Very low weight
  • Auto Timing Feature
  • Smooth Response

Specifications:

  • 22mmx11.8mmx3.84mm
  • 1.9g

 

From Airbot

BLHeli_32 is the third generation BLHeli code, following base BLHeli and BLHeli_S.

BLHeli_32 runs on an ARM 32bit MCU, initially it will be on a Cortex-M0 running at 48MHz, but there are MCUs out there that can run a lot faster.

So what can the increased MCU speed do?
First of all, it can run input signals with lower latency at faster rates.
Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported.

Secondly it allows packing of more functionality.
– Like programmable pwm frequency, up to 48kHz, that can run motors even smoother, and also allows for moving of small but potentially disturbing humps in the throttle response. All ESCs have these bumps, with BLHeli_32 they can now be moved in the rpm range, to a place where the system has low sensitivity to them.

– Like auto timing. Which is not the option to choose if you’re after max power. But if you want the most efficient running with very good robustness against desync, it is the perfect choice.

– Like voltage and current limiting. Which is implemented in the code, and will be supported on some ESCs. Voltage limiting is desirable for fixed wing crafts. And current limiting adds protection against ESC failure.

– Like programmable brake on stop force. Which allows control of the braking of fixed wing props.

– Like improved direction change in bidirectional mode.

– Like more to come in the future. Such as setup from the FC by using Dshot commands. Such as telemetry functionality. There is room to grow performance and functionality.

 

Programming parameters:

Rampup Power:

Rampup power can be set to relative values from 3% to 150%. This is the maximum power that is allowed when ramping up at low rpms and during startup. For low rpms, the maximum power to the motor is limited, in order to facilitate detection of low BEMF voltages.

Rampup power also affects bidirectional operation, as the parameter is used to limit the power applied during direction reversal.

During startup, the actual applied power depends on throttle input, and can be lower than the maximum level set by the rampup power parameter, but the minimum level is a quarter of the maximum level.

Motor Timing:

Motor timing can be set between approximately 10 and approximately 310 in approximately 10 increments (actual accurate values here are 15/16ths of a degree).

Typically a medium setting will work fine, but if the motor stutters it can be beneficial to increase timing. Some motors with high inductance can have a very long commutation demagnetization time. This can result in motor stop or stutter upon quick throttle increase, particularly when running at a low rpm. Setting timing higher will allow more time for demagnetization, and often helps.

This parameter can also be set to auto. I this case the code monitors demagnetization time, and keeps timing as low as possible without having issues with demag. On well behaved motors, timing can be low in the entire power range, and thereby max power can be reduced. On not so well behaved motors, timing is increased as needed, and thereby improves margins against sync loss.

PWM frequency:

Motor pwm frequency can be programmed between 16kHz and 48kHz. Higher pwm frequency can run motors smoother. Programmable frequency also allows for moving of small but potentially disturbing humps in the throttle response. All ESCs have these bumps, with BLHeli_32 they can be moved in the rpm range, to a place where the system has low sensitivity to them.

Demag Compensation:

Demag compensation is a feature to protect from motor stalls caused by long winding demagnetization time after commutation. The typical symptom is motor stop or stutter upon quick throttle increase, particularly when running at a low rpm. As mentioned above, setting high commutation timing normally helps, but at the cost of efficiency.

Demag compensation is an alternative way of combating the issue. First of all, it detects when a demag situation occurs.

– In this situation, there is no info on motor timing, and commutation proceeds blindly with a predicted timing.
– In addition to this, motor power is cut off some time before the next commutation.

A metric is calculated that indicates how severe the demag situation is. The more severe the situation, the more power is cut off. When demag compensation is set to off, power is never cut. When setting it to low or high, power is cut. For a high setting, power is cut more aggressively.
Generally, a higher value of the compensation parameter gives better protection.

If demag compensation is set too high, maximum power can be somewhat reduced for some motors.

Maximum Acceleration:

Maximum acceleration can be set between 0.1%/ms and 25.5%/ms. It can also be set to maximum, in which case acceleration is not limited. Limiting acceleration is primarily intended as a backup parameter that can be used in cases where too hard acceleration gives desyncs.

When setting to e.g. 10%/ms, it means that the power applied to the motor is not allowed to increase by more than 10% per millisecond.

 

Throttle Cal Enable:

If disabled, throttle calibration is disabled.

Minimum throttle, maximum throttle and center throttle:

These settings set the throttle range of the ESC. Center throttle is only used for bidirectional operation. The values given for these settings are for a normal 1000us to 2000us input signal, and for the other input signals, the values must be scaled.

For Dshot input signal, these settings have no effect.

 

Low Voltage Protection:

Low voltage protection can be set between 2.5V and 4.0V per lipo cell. Or it can be disabled.

When enabled, it will limit power applied to the motor if the battery voltage drops below the programmed threshold. This feature is primarily intended for fixed wing crafts.

Current Protection:

Current protection can be enabled to limit current. If enabled, then current will be limited to maximum the programmed value. The reaction time of the current limiting is quite fast, so current will also be limited during accelerations.

 

 

Input signal:

Available throttle calibration range is from 1000us to 2000us, and the difference between minimum and maximum throttle must be more than 140us (70us in bidirectional mode). If a calibration is done where the difference is less than 140us (70us), the maximum will be shifted so that the difference is 140us (70us).

Oneshot125 mode works just the same as regular 1-2ms mode, the only difference is that all timing is divided by 8. And the same for Oneshot42, where all timing is further divided by 3. Multishot also works similarly, except the input signal range is 5-25us.

Dshot is supported at any rate, up to at least Dshot1200. When the input signal is Dshot, throttle calibration is disabled, and the throttle calibration values are ignored.

Input signal rates up to at least 32kHz are supported. But please note that higher input signal rates put a heavier load on the MCU, and will reduce the maximum erpm that the ESC can handle.

 

 

 

Dit artikel is aan ons assortiment toegevoegd op dinsdag 15 augustus, 2017.
Recensies
Klanten die dit artikel kochten, kochten ook:
KF-77 Cobra CP-1407-4100 Champion Series Multirotor Motor Kv4100
KF-77 Cobra CP-1407-4100 Champion Series Multirotor Motor Kv4100
Winkelwagen  meer
Uw winkelwagen is leeg.
Snelzoeken
 
Gebruik trefwoorden om te vinden wat u zoekt
Uitgebreid zoeken
Notificaties  meer
NotificatiesHou me op de hoogte van updates op KF-68 Wraith32 Mini BLHELI32 ESC, 2-6S, 25A, 10x20mm
Vertel het verder
 
Vertel iemand over dit artikel.

(c) KDS-RC-HeliShop 2010